Product CenterPRODUCTS
All products
Refrigerated dryer
adsorption type dryer
Combined dryer
Compression heat dryer
Blower heated dessIcant air dryer
Modular dryer
Special gas dryer
water chilling unit
Compressed air filter
Stainless steel compressed air filter
High efficiency oil remover
Waste oil collector
Self-cleaning filter
Oil water separator
Rear cooler
Drainer
Compressed waste heat adsorption dryer
Product featuresThe compressor waste heat dryer uses the waste heat of oil-free air compressor to heat and regenerate the adsorbent; Make full use of the waste heat in the compressed air system. Under
- Product features
- Product specification
- Accessories
-
Product featuresThe compressor waste heat dryer uses the waste heat of oil-free air compressor to heat and regenerate the adsorbent; Make full use of the waste heat in the compressed air system. Under the condition of not using the heating device, it can also achieve the effect of heating the dryer, fully showing its energy-saving characteristics. The dew point of the product gas can reach - 40 ℃. The self-developed PLC controller is more stable and reliable than the single chip microcomputer. The control valve adopts butterfly valve to ensure no fault switching for more than 1 million times. The advanced diverter design enables the compressed air to contact the adsorbent evenly, eliminating the phenomenon of channeling.Unique tiering technologyThe layering technology independently developed by the company makes the air preliminarily dried through aluminum oxide. After reducing the water content in the air, it is deeply dried through molecular sieve to achieve the air quality with low dew point.working principleThe high-temperature air discharged from the air compressor has two properties: high heat and high unsaturation. The waste heat series products use this original compressed air to heat and regenerate the adsorbent, which saves the electric heating power consumption required by the micro heat dryer series and consumes the gas consumption at this stage. After the heating and regeneration, the original compressed air directly enters the water cooler for cooling and then enters the adsorption tower for adsorption to obtain the dried finished gas, We take 1.5% of the finished product gas for cold blowing regeneration of the heated adsorbent. After the cold blowing, the double tower switch is completed and the cycle is repeated.Operating conditions and technical indicatorsPower: 220V/50HZWorking pressure: 0.6~1.0MpaPressure drop: ≤ 0.04MpaInlet temperature: 110 ℃ - 140 ℃Cooling water inlet pressure: 0.2-0.4MpaCooling water inlet temperature: ≤ 32 ℃Dew point: - 12.2 ℃~- 40 ℃Purge air: ≤ 1%
-
model
Treatment gas volume
Company：Nm³/min
weight KG
Power consumption W
Import and export
Flange size
Overall dimensions
cooling water
Circulation volume：Nm³/min
long
wide
high
DM150YR
15
1000
150
DN65
2000
1400
2500
6
DM180YR
18
1200
2000
1500
2800
7
DM200YR
22
1650
2000
1500
3000
8
DM250YR
25
1880
DN80
2300
1800
2800
10
DM300YR
30
2000
2300
1800
3000
12
DM350YR
35
2200
DN100
2300
1800
3000
13
DM400YR
45
2350
200
2840
2050
3000
15
DM500YR
55
2500
2500
2000
3000
17.3
DM600YR
65
2800
2500
2000
3100
19
DM800YR
85
3250
DN125
3200
3200
3200
23
DM1000YR
100
4350
3500
2200
3200
31
DM1200YR
120
5000
DN150
3900
2200
3500
35
DM1500YR
150
6500
3900
2200
3400
39
DM2000YR
200
7800
4500
3700
3800
46
DM2500YR
250
9700
DN200
4800
2800
3800
58
DM3000YR
300
12500
4800
2800
3800
68
DM3500YR
350
13100
350
4800
2800
3900
78
DM4000YR
400
13700
5100
3000
3900
84
Online consultation
Online consulting
Buyers are still watchingBuyers are still watching
